Rechercher

Coupures intempestives !

Coupures intempestives !

Démarré par sebdepringy, 15 Août 2021 à 19:42:20

« précédent - suivant »

0 Membres et 2 Invités sur ce sujet

Imprimer
En bas Pages 1 ... 5 6 7
Actions de l'utilisateur
#90
16 Décembre 2021 à 10:09:13
j'ai essayé les 3 cela fait pareil pour les 3, j'ai lancé mes synchro hier, toute les 3h cela coupe

Dec 15 17:54:27 ntpd: Initial clock set
Dec 15 17:54:28 rc_service: ntpd_synced 2404:notify_rc restart_diskmon
Dec 15 17:54:28 disk_monitor: Finish
Dec 15 17:54:28 disk_monitor: be idle
Dec 15 17:54:28 kernel: Archer TCP Pure ACK Enabled
Dec 15 17:54:28 rc_service: udhcpc 2203:notify_rc stop_samba
Dec 15 17:54:28 rc_service: udhcpc 2203:notify_rc start_samba
Dec 15 17:54:28 rc_service: waitting "stop_samba" via udhcpc ...
Dec 15 17:54:29 Samba_Server: smb daemon is stopped
Dec 15 17:54:30 dhcp_client: bound 185.251.xxx.xxx/255.255.252.0 via 185.251.163.254 for 300 seconds.
Dec 15 17:54:30 Samba_Server: daemon is started
Dec 15 17:56:03 rc_service: httpd 1338:notify_rc restart_wan_if 0;restart_stubby
Dec 15 17:56:05 WAN_Connection: WAN(0) link down.
Dec 15 17:56:05 wan: finish adding multi routes
Dec 15 17:56:08 BWDPI: fun bitmap = 57f
Dec 15 17:56:11 kernel: Archer TCP Pure ACK Enabled
Dec 15 17:56:11 rc_service: udhcpc 2792:notify_rc stop_samba
Dec 15 17:56:11 rc_service: udhcpc 2792:notify_rc start_samba
Dec 15 17:56:11 rc_service: waitting "stop_samba" via udhcpc ...
Dec 15 17:56:12 Samba_Server: smb daemon is stopped
Dec 15 17:56:13 dhcp_client: bound 185.251.xxx.xxx/255.255.252.0 via 185.251.163.254 for 300 seconds.
Dec 15 17:56:13 Samba_Server: daemon is started
Dec 15 17:56:40 WAN_Connection: WAN was restored.
Dec 15 17:56:56 rc_service: httpd 1338:notify_rc restart_wan_if 0;restart_stubby
Dec 15 17:56:59 wan: finish adding multi routes
Dec 15 17:57:02 BWDPI: fun bitmap = 57f
Dec 15 17:57:04 kernel: Archer TCP Pure ACK Enabled
Dec 15 17:57:04 rc_service: udhcpc 3179:notify_rc stop_samba
Dec 15 17:57:04 rc_service: udhcpc 3179:notify_rc start_samba
Dec 15 17:57:04 rc_service: waitting "stop_samba" via udhcpc ...
Dec 15 17:57:04 Samba_Server: smb daemon is stopped
Dec 15 17:57:05 dhcp_client: bound 185.251.xxx.xxx/255.255.252.0 via 185.251.163.254 for 300 seconds.
Dec 15 17:57:05 Samba_Server: daemon is started
Dec 15 17:57:42 rc_service: httpd 1338:notify_rc restart_wan_if 0;restart_stubby
Dec 15 17:57:44 wan: finish adding multi routes
Dec 15 17:57:47 BWDPI: fun bitmap = 57f
Dec 15 17:57:49 kernel: Archer TCP Pure ACK Enabled
Dec 15 17:57:49 rc_service: udhcpc 3521:notify_rc stop_samba
Dec 15 17:57:49 rc_service: udhcpc 3521:notify_rc start_samba
Dec 15 17:57:49 rc_service: waitting "stop_samba" via udhcpc ...
Dec 15 17:57:49 Samba_Server: smb daemon is stopped
Dec 15 17:57:50 dhcp_client: bound 185.251.xxx.xxx/255.255.252.0 via 185.251.163.254 for 300 seconds.
Dec 15 17:57:50 Samba_Server: daemon is started
Dec 16 02:45:47 kernel: eth0 (Int switch port: 0) (Logical Port: 0) (phyId: 8) Link DOWN.
Dec 16 02:45:49 kernel: eth0: sysport_tm port shaper set to 999000 kbps (phy speed 1000000 kbps)
Dec 16 02:45:49 kernel: eth0 (Int switch port: 0) (Logical Port: 0) (phyId: 8) Link Up at 1000 mbps full duplex
Dec 16 02:45:52 wan: finish adding multi routes
Dec 16 02:45:52 WAN_Connection: WAN was restored.
Dec 16 02:46:00 BWDPI: fun bitmap = 57f
Dec 16 02:46:02 kernel: Archer TCP Pure ACK Enabled
Dec 16 02:46:02 rc_service: udhcpc 19590:notify_rc stop_samba
Dec 16 02:46:02 rc_service: udhcpc 19590:notify_rc start_samba
Dec 16 02:46:02 rc_service: waitting "stop_samba" via udhcpc ...
Dec 16 02:46:02 Samba_Server: smb daemon is stopped
Dec 16 02:46:03 dhcp_client: bound 185.251.xxx.xxx/255.255.252.0 via 185.251.163.254 for 300 seconds.
Dec 16 02:46:03 Samba_Server: daemon is started
Dec 16 02:46:06 kernel: eth0 (Int switch port: 0) (Logical Port: 0) (phyId: 8) Link DOWN.
Dec 16 02:46:08 kernel: eth0: sysport_tm port shaper set to 999000 kbps (phy speed 1000000 kbps)
Dec 16 02:46:08 kernel: eth0 (Int switch port: 0) (Logical Port: 0) (phyId: 8) Link Up at 1000 mbps full duplex
Dec 16 02:46:12 WAN_Connection: WAN(0) link up.
Dec 16 02:46:12 rc_service: wanduck 1154:notify_rc restart_wan_if 0
Dec 16 02:46:14 wan: finish adding multi routes
Dec 16 02:46:17 WAN_Connection: WAN was restored.
Dec 16 02:46:22 BWDPI: fun bitmap = 57f
Dec 16 02:46:23 kernel: Archer TCP Pure ACK Enabled
Dec 16 02:46:23 rc_service: udhcpc 19850:notify_rc stop_samba
Dec 16 02:46:23 rc_service: udhcpc 19850:notify_rc start_samba
Dec 16 02:46:23 rc_service: waitting "stop_samba" via udhcpc ...
Dec 16 02:46:23 Samba_Server: smb daemon is stopped
Dec 16 02:46:24 dhcp_client: bound 185.251.xxx.xxx/255.255.252.0 via 185.251.163.254 for 300 seconds.
Dec 16 02:46:25 Samba_Server: daemon is started
Dec 16 03:00:46 kernel: eth0 (Int switch port: 0) (Logical Port: 0) (phyId: 8) Link DOWN.
Dec 16 03:00:49 kernel: eth0: sysport_tm port shaper set to 999000 kbps (phy speed 1000000 kbps)
Dec 16 03:00:49 kernel: eth0 (Int switch port: 0) (Logical Port: 0) (phyId: 8) Link Up at 1000 mbps full duplex
Dec 16 03:00:51 WAN_Connection: WAN(0) link up.
Dec 16 03:00:51 rc_service: wanduck 1154:notify_rc restart_wan_if 0
Dec 16 03:00:54 wan: finish adding multi routes
Dec 16 03:00:59 WAN_Connection: WAN was restored.
Dec 16 03:01:02 BWDPI: fun bitmap = 57f
Dec 16 03:01:04 kernel: Archer TCP Pure ACK Enabled
Dec 16 03:01:04 rc_service: udhcpc 22078:notify_rc stop_samba
Dec 16 03:01:04 rc_service: udhcpc 22078:notify_rc start_samba
Dec 16 03:01:04 rc_service: waitting "stop_samba" via udhcpc ...
Dec 16 03:01:04 Samba_Server: smb daemon is stopped
Dec 16 03:01:05 dhcp_client: bound 185.251.xxx.xxx/255.255.252.0 via 185.251.163.254 for 300 seconds.
Dec 16 03:01:05 Samba_Server: daemon is started
Dec 16 05:16:10 kernel: eth0 (Int switch port: 0) (Logical Port: 0) (phyId: 8) Link DOWN.
Dec 16 05:16:13 kernel: eth0: sysport_tm port shaper set to 999000 kbps (phy speed 1000000 kbps)
Dec 16 05:16:13 kernel: eth0 (Int switch port: 0) (Logical Port: 0) (phyId: 8) Link Up at 1000 mbps full duplex
Dec 16 05:16:17 wan: finish adding multi routes
Dec 16 05:16:21 WAN_Connection: WAN was restored.
Dec 16 05:16:26 BWDPI: fun bitmap = 57f
Dec 16 05:16:27 kernel: Archer TCP Pure ACK Enabled
Dec 16 05:16:27 rc_service: udhcpc 7651:notify_rc stop_samba
Dec 16 05:16:27 rc_service: udhcpc 7651:notify_rc start_samba
Dec 16 05:16:27 rc_service: waitting "stop_samba" via udhcpc ...
Dec 16 05:16:27 Samba_Server: smb daemon is stopped
Dec 16 05:16:28 dhcp_client: bound 185.251.xxx.xxx/255.255.252.0 via 185.251.163.254 for 300 seconds.
Dec 16 05:16:28 Samba_Server: daemon is started
Dec 16 09:01:14 kernel: eth0 (Int switch port: 0) (Logical Port: 0) (phyId: 8) Link DOWN.
Dec 16 09:01:16 kernel: eth0: sysport_tm port shaper set to 999000 kbps (phy speed 1000000 kbps)
Dec 16 09:01:16 kernel: eth0 (Int switch port: 0) (Logical Port: 0) (phyId: 8) Link Up at 1000 mbps full duplex
Dec 16 09:01:22 wan: finish adding multi routes
Dec 16 09:01:23 WAN_Connection: WAN was restored.
Dec 16 09:01:30 BWDPI: fun bitmap = 57f
Dec 16 09:01:31 kernel: Archer TCP Pure ACK Enabled
Dec 16 09:01:31 rc_service: udhcpc 5285:notify_rc stop_samba
Dec 16 09:01:32 rc_service: udhcpc 5285:notify_rc start_samba
Dec 16 09:01:32 rc_service: waitting "stop_samba" via udhcpc ...
Dec 16 09:01:32 Samba_Server: smb daemon is stopped
Dec 16 09:01:33 dhcp_client: bound 185.251.xxx.xxx/255.255.252.0 via 185.251.163.254 for 300 seconds.
Dec 16 09:01:33 Samba_Server: daemon is started
#91
16 Décembre 2021 à 10:14:16
On voit pas mal de flap physique

Code Sélectionner
Dec 16 03:00:46 kernel: eth0 (Int switch port: 0) (Logical Port: 0) (phyId: 8) Link DOWN.
Dec 16 03:00:49 kernel: eth0: sysport_tm port shaper set to 999000 kbps (phy speed 1000000 kbps)
Dec 16 03:00:49 kernel: eth0 (Int switch port: 0) (Logical Port: 0) (phyId: 8) Link Up at 1000 mbps full duplex
Dec 16 03:00:51 WAN_Connection: WAN(0) link up.


Je dirais un problème matériel. Soit l'ONT, soit ton routeur, soit le cable entre les deux. Ca peut aussi venir d'une alimentation un peu faiblarde qui ne tient pas quand le CPU bosse un peu.
Offre: K-Net Pulse 1Gb/s symétrique Sosh 300Mb/s symétrique
Routeur: Mikrotik RB4011
Switch: Netgear GS110TP, Cisco SG200
AP Wi-Fi: Ubiquiti UAP-AC-Lite
Uptime: https://uptime.loiklo.net/
#92
16 Décembre 2021 à 10:38:04
Ouais c'est ce que je dis depuis des semaines...
#93
16 Décembre 2021 à 19:27:06
Citation de: Hugues le 16 Décembre 2021 à 10:38:04
Ouais c'est ce que je dis depuis des semaines...

Effectivement, ça me paraît plutôt clair.

Citation de: halesk2k le 16 Décembre 2021 à 10:14:16
Je dirais un problème matériel. Soit l'ONT, soit ton routeur, soit le cable entre les deux. Ca peut aussi venir d'une alimentation un peu faiblarde qui ne tient pas quand le CPU bosse un peu.

Tout est dit.
#94
16 Décembre 2021 à 19:35:16
Citation de: halesk2k le 16 Décembre 2021 à 10:14:16
On voit pas mal de flap physique

Code Sélectionner
Dec 16 03:00:46 kernel: eth0 (Int switch port: 0) (Logical Port: 0) (phyId: 8) Link DOWN.
Dec 16 03:00:49 kernel: eth0: sysport_tm port shaper set to 999000 kbps (phy speed 1000000 kbps)
Dec 16 03:00:49 kernel: eth0 (Int switch port: 0) (Logical Port: 0) (phyId: 8) Link Up at 1000 mbps full duplex
Dec 16 03:00:51 WAN_Connection: WAN(0) link up.


Je dirais un problème matériel. Soit l'ONT, soit ton routeur, soit le cable entre les deux. Ca peut aussi venir d'une alimentation un peu faiblarde qui ne tient pas quand le CPU bosse un peu.

ok l'alimentation de l'ONT, le premier truc que l'abruti de technicien covage a fait est de virer le mien, je remet le mien donc ? ensuite soit disant essaie mais " a vide" donc forcement pas trop solicité

cable rj45 deja fait
routeur aussi

le dhcp j'ai remis en "normal"
#95
17 Décembre 2021 à 16:13:52 Dernière édition: 17 Décembre 2021 à 16:15:48 par sebdepringy
Dec 17 02:57:29 kernel: eth0 (Int switch port: 0) (Logical Port: 0) (phyId: 8) Link DOWN.
Dec 17 02:57:32 kernel: eth0: sysport_tm port shaper set to 999000 kbps (phy speed 1000000 kbps)
Dec 17 02:57:32 kernel: eth0 (Int switch port: 0) (Logical Port: 0) (phyId: 8) Link Up at 1000 mbps full duplex
Dec 17 02:57:58 acsd: eth5: COEX: downgraded chanspec 0x180b to 0x1009: channel 6 used by exiting BSSs
Dec 17 02:59:19 wan: finish adding multi routes
Dec 17 02:59:26 WAN_Connection: WAN was restored.
Dec 17 02:59:27 BWDPI: fun bitmap = 57f
Dec 17 02:59:29 kernel: Archer TCP Pure ACK Enabled
Dec 17 02:59:29 rc_service: udhcpc 5243:notify_rc stop_samba
Dec 17 02:59:29 rc_service: udhcpc 5243:notify_rc start_samba
Dec 17 02:59:29 rc_service: waitting "stop_samba" via udhcpc ...
Dec 17 02:59:29 Samba_Server: smb daemon is stopped
Dec 17 02:59:30 dhcp_client: bound 185.251.xxx.xxx/255.255.252.0 via 185.251.163.254 for 300 seconds.
Dec 17 02:59:30 Samba_Server: daemon is started
Dec 17 03:10:44 wlceventd: wlceventd_proc_event(505): eth6: Auth 44:07:0B:E1:68:1A, status: Successful (0)
Dec 17 03:10:44 wlceventd: wlceventd_proc_event(534): eth6: Assoc 44:07:0B:E1:68:1A, status: Successful (0)
Dec 17 03:13:04 acsd: eth5: COEX: downgraded chanspec 0x180b to 0x1009: channel 6 used by exiting BSSs
Dec 17 03:18:50 kernel: eth0 (Int switch port: 0) (Logical Port: 0) (phyId: 8) Link DOWN.
Dec 17 03:18:53 kernel: eth0: sysport_tm port shaper set to 999000 kbps (phy speed 1000000 kbps)
Dec 17 03:18:53 kernel: eth0 (Int switch port: 0) (Logical Port: 0) (phyId: 8) Link Up at 1000 mbps full duplex
Dec 17 03:18:56 WAN_Connection: WAN(0) link up.
Dec 17 03:18:56 rc_service: wanduck 1153:notify_rc restart_wan_if 0
Dec 17 03:18:59 wan: finish adding multi routes
Dec 17 03:19:04 WAN_Connection: WAN was restored.
Dec 17 03:19:07 BWDPI: fun bitmap = 57f
Dec 17 03:19:09 kernel: Archer TCP Pure ACK Enabled
Dec 17 03:19:09 rc_service: udhcpc 8566:notify_rc stop_samba
Dec 17 03:19:09 rc_service: udhcpc 8566:notify_rc start_samba
Dec 17 03:19:09 rc_service: waitting "stop_samba" via udhcpc ...
Dec 17 03:19:10 Samba_Server: smb daemon is stopped
Dec 17 03:19:11 dhcp_client: bound 185.251.xxx.xxx/255.255.252.0 via 185.251.163.254 for 300 seconds.
Dec 17 03:19:11 Samba_Server: daemon is started
Dec 17 03:28:09 acsd: eth5: COEX: downgraded chanspec 0x180b to 0x1009: channel 6 used by exiting BSSs
Dec 17 03:40:09 kernel: eth0 (Int switch port: 0) (Logical Port: 0) (phyId: 8) Link DOWN.
Dec 17 03:40:11 kernel: eth0: sysport_tm port shaper set to 999000 kbps (phy speed 1000000 kbps)
Dec 17 03:40:11 kernel: eth0 (Int switch port: 0) (Logical Port: 0) (phyId: 8) Link Up at 1000 mbps full duplex
Dec 17 03:41:47 wan: finish adding multi routes
Dec 17 03:41:47 WAN_Connection: WAN was restored.
Dec 17 03:41:55 BWDPI: fun bitmap = 57f
Dec 17 03:41:56 kernel: Archer TCP Pure ACK Enabled
Dec 17 03:41:56 rc_service: udhcpc 12322:notify_rc stop_samba
Dec 17 03:41:56 rc_service: udhcpc 12322:notify_rc start_samba
Dec 17 03:41:56 rc_service: waitting "stop_samba" via udhcpc ...
Dec 17 03:41:58 Samba_Server: smb daemon is stopped
Dec 17 03:41:58 dhcp_client: bound 185.251.xxx.xxx/255.255.252.0 via 185.251.163.254 for 300 seconds.
Dec 17 03:41:58 Samba_Server: daemon is started
Dec 17 03:43:14 acsd: eth5: COEX: downgraded chanspec 0x180b to 0x1009: channel 6 used by exiting BSSs
Dec 17 03:58:20 acsd: eth5: COEX: downgraded chanspec 0x180b to 0x1009: channel 6 used by exiting BSSs
Dec 17 04:01:12 kernel: eth0 (Int switch port: 0) (Logical Port: 0) (phyId: 8) Link DOWN.
Dec 17 04:01:15 kernel: eth0: sysport_tm port shaper set to 999000 kbps (phy speed 1000000 kbps)
Dec 17 04:01:15 kernel: eth0 (Int switch port: 0) (Logical Port: 0) (phyId: 8) Link Up at 1000 mbps full duplex
Dec 17 04:02:24 wan: finish adding multi routes
Dec 17 04:02:30 WAN_Connection: WAN was restored.
Dec 17 04:02:32 BWDPI: fun bitmap = 57f
Dec 17 04:02:34 kernel: Archer TCP Pure ACK Enabled
Dec 17 04:02:34 rc_service: udhcpc 15743:notify_rc stop_samba
Dec 17 04:02:34 rc_service: udhcpc 15743:notify_rc start_samba
Dec 17 04:02:34 rc_service: waitting "stop_samba" via udhcpc ...
Dec 17 04:02:34 Samba_Server: smb daemon is stopped
Dec 17 04:02:35 dhcp_client: bound 185.251.xxx.xxx/255.255.252.0 via 185.251.163.254 for 300 seconds.
Dec 17 04:02:35 Samba_Server: daemon is started
Dec 17 04:13:26 acsd: eth5: COEX: downgraded chanspec 0x180b to 0x1009: channel 6 used by exiting BSSs
Dec 17 04:26:40 wlceventd: wlceventd_proc_event(469): eth6: Deauth_ind 44:07:0B:E1:68:1A, status: 0, reason: Deauthenticated because sending station is leaving (or has left) IBSS or ESS (3)
Dec 17 04:28:31 acsd: eth5: COEX: downgraded chanspec 0x180b to 0x1009: channel 6 used by exiting BSSs
Dec 17 04:31:13 kernel: eth0 (Int switch port: 0) (Logical Port: 0) (phyId: 8) Link DOWN.
Dec 17 04:31:15 kernel: eth0: sysport_tm port shaper set to 999000 kbps (phy speed 1000000 kbps)
Dec 17 04:31:15 kernel: eth0 (Int switch port: 0) (Logical Port: 0) (phyId: 8) Link Up at 1000 mbps full duplex
Dec 17 04:31:18 WAN_Connection: WAN(0) link up.
Dec 17 04:31:18 rc_service: wanduck 1153:notify_rc restart_wan_if 0
Dec 17 04:31:21 wan: finish adding multi routes
Dec 17 04:31:23 WAN_Connection: WAN was restored.
Dec 17 04:31:30 BWDPI: fun bitmap = 57f
Dec 17 04:31:31 kernel: Archer TCP Pure ACK Enabled
Dec 17 04:31:31 rc_service: udhcpc 20478:notify_rc stop_samba
Dec 17 04:31:31 rc_service: udhcpc 20478:notify_rc start_samba
Dec 17 04:31:31 rc_service: waitting "stop_samba" via udhcpc ...
Dec 17 04:31:32 Samba_Server: smb daemon is stopped
Dec 17 04:31:33 dhcp_client: bound 185.251.xxx.xxx/255.255.252.0 via 185.251.163.254 for 300 seconds.
Dec 17 04:31:33 Samba_Server: daemon is started
Dec 17 04:43:36 acsd: eth5: COEX: downgraded chanspec 0x180b to 0x1009: channel 6 used by exiting BSSs
Dec 17 04:58:42 acsd: eth5: COEX: downgraded chanspec 0x180b to 0x1009: channel 6 used by exiting BSSs
Dec 17 05:01:08 kernel: eth0 (Int switch port: 0) (Logical Port: 0) (phyId: 8) Link DOWN.
Dec 17 05:01:11 kernel: eth0: sysport_tm port shaper set to 999000 kbps (phy speed 1000000 kbps)
Dec 17 05:01:11 kernel: eth0 (Int switch port: 0) (Logical Port: 0) (phyId: 8) Link Up at 1000 mbps full duplex
Dec 17 05:01:15 WAN_Connection: WAN(0) link up.
Dec 17 05:01:15 rc_service: wanduck 1153:notify_rc restart_wan_if 0
Dec 17 05:01:17 wan: finish adding multi routes
Dec 17 05:01:20 WAN_Connection: WAN was restored.
Dec 17 05:01:26 BWDPI: fun bitmap = 57f
Dec 17 05:01:27 kernel: Archer TCP Pure ACK Enabled
Dec 17 05:01:27 rc_service: udhcpc 25376:notify_rc stop_samba
Dec 17 05:01:27 rc_service: udhcpc 25376:notify_rc start_samba
Dec 17 05:01:27 rc_service: waitting "stop_samba" via udhcpc ...
Dec 17 05:01:27 Samba_Server: smb daemon is stopped
Dec 17 05:01:28 dhcp_client: bound 185.251.xxx.xxx/255.255.252.0 via 185.251.163.254 for 300 seconds.
Dec 17 05:01:28 Samba_Server: daemon is started


C'est souvent la nuit quand même les coupures...
#96
21 Décembre 2021 à 13:21:41
Donc ONT ?

A partir du moment ou le lien est down même si l'ont est alumé c'est l'ONT ou Routeur?
#97
21 Décembre 2021 à 13:23:30
C'est toujours l'ONT :D

perso ce que je ferais, c'est que je le débrancherais, je contracterais K-Net, je dirais que l'ONT a rendu l'âme.. Ils seront bien obligés d'en faire envoyer un nouveau.
Par contre, il ne faut pas le rebrancher entre temps, sous peine de voir le ticket fermé.
#98
21 Décembre 2021 à 15:18:04
ouais sauf que j'ai besoin d'internet....... je peux pas rester sans
Imprimer
En haut Pages 1 ... 5 6 7
Actions de l'utilisateur

Coupures intempestives !